Realisitic
TRC-430
Documentation Project
CBTricks.com
SPECIFICATIONS
General
|
Transmitter |
Crystal
controlled PLL synthesizer, |
|
Receiver |
Crystal
controlled double conversion, |
|
Communicating frequencies |
40 CB channels (26.965 to 27.405MHz) |
|
Voltage operation |
12-16V DC(negative ground) |
|
Temperature and Humidity range |
-22ºF-
+140ºF (-30ºC-- +60ºC) |
|
Transmitter/Receiver switching |
Electrical |
Standard Test Conditions
|
Battery supply voltage |
13.8V DC |
|
Modulation |
1000 Hz, 30% |
|
Receiver output power |
500mW at external SP |
|
Receiver output impedance |
8 ohms, non-inductive |
|
Ant. load impedance of transmitter |
50 ohms, non-inductive |
|
Ambient conditions |
|
|
Temperature |
63ºF-73ºF (17ºC-23ºC) |
|
Humidity |
40% - 70% |
Transmitter
|
Description |
Nominal |
Limit |
|
RF power output |
4.0 watts |
3.6-4.4 watts |
|
Antenna spurious emission |
70 |
50 |
|
Modulation capability (positive/negative) |
+90%/-90% |
+80%/-80% |
|
AMC Range at 1 kHz |
40 dB |
30dB |
|
Frequency accuracy |
0.002% |
0.005% |
|
Spurious radiation & Harmonic |
||
|
Signal radiation ratio from fundamental |
-65dB |
-60dB |
|
Current consumption |
||
|
At no modulation |
1000mA |
1200mA |
|
At 80% modulation |
1500mA |
1700mA |
|
Envelope distortion |
10% max. 1000Hz, 50% mod. |
|
|
Stability against variation of antenna impedance |
Satisfactory when dummy antenna is varied from 40 ohms to 200 ohms. |
|
Receiver
|
Description |
Nominal |
Limit |
|
Intermediate frequency |
|
|
|
1st IF |
10.695 MHz |
|
|
2nd IF |
455 kHz |
|
|
Sensitivity for 500mW output |
0.3uV |
1uV |
|
Sensitivity at 10dB S+ N/N |
0.7uV |
1.0uV |
|
Adjacent channel rejection |
65dB |
55dB |
|
Image rejection (1st IF/2nd IF) |
70dB |
60dB |
|
IF rejection ratio (1st IF/2nd IF) |
60dB |
45dB |
|
Signal-to-Noise ratio at 1mV input |
40dB |
35dB |
|
Distortion at 1mv input, 30% mod. (500mW out) |
3% |
5% |
|
AGC Figure of merit at 5OmV input |
80dB |
70 dB |
|
Power output at 1 mV input |
|
|
|
Undistorted (10% THD) |
4.5W |
4.0W |
|
Maximum |
5.0W |
4.5W |
|
Electrical fidelity compared to 1000 Hz |
|
|
|
450 Hz |
-6dB |
-6±3dB |
|
2500 Hz |
-6dB |
-6±3dB |
|
Cross modulation |
50dB |
40dB |
|
Squelch |
60dB |
60±6dB |
|
Current consumption (no signal) |
250mA |
300mA |
|
"5" meter sensitivity to light 3th LED |
40dB |
40±6dB |
|
Automatic noise limiter |
16dB |
12dB |
Public Address
|
Description |
Nominal |
Limit |
|
10% THD output power |
4W |
3.5W |
|
Microphone sensitivity for 4W |
5mV |
10mV |
|
Current drain at 10% THD power |
1000mA |
1200mA |
Other Items
|
Fuse |
WHT wire: 1Amp.RED wire: 2 Amp. |
|
General power requirement |
12-16VDC |
|
Dimensions |
(W)4
11/15" (l20mm)x |
|
Weight |
1lb 12ozs (787g) |
Note: Nominal specs represent the design specs; all units should be able to approximate these some will exceed and same may drop slightly below these specs. Limit specs represent the absolute worst condition that still might be considered acceptable; in no case should a unit perform to less than any limit spec.