Galaxy DX Radios DX95T
Documentation Project

CBTricks.com

Transmitter Alignment
See Alignment Locations

SETTINGS CONNECTION
ADJUST
ADJUST FOR
Remove TP7-TP9 Jumper PCB.
TX CARRIER OSCILLATORS:
AM TX Mode

Band E CH. 1 
Connect Frequency Counter to TP6
L25
LSB/TX mode: Adjust for 10.6975MHz ±20Hz.
Connect Frequency Counter to TP6 
L24
USB/TX mode: Adjust for 10.6925MHz ±20 Hz.
Connect Frequency Counter to TP5
L23
AM/TX mode: Adjust for 10.6950MHz ±20 Hz.
DRIVER BIAS: (2SC2166)
Set Radio to: 

Band E, Ch.1

Mode to USB

MIKE GAIN at minimum.
Connect DC Ammeter between TP7 and TP9. 
VR12
Key TX adjust for 75mA.
FINAL BIAS: (2SC2312)
Set Radio to: 

Band E, Ch.1 

Mode to USB

MIKE GAIN at minimum
Connect DC Ammeter between TP7 and TP8. 
VR10 
Key TX & adjust for 50mA.
Replace TP7-TP9 Jumper PCB.
RF AMP CHAIN:
Set mode to AM.
Set RF power control fully clockwise.
Connect wattmeter to ANT output. 
L44, L43, 
L42, L40,


L44 
Key TX & adjust (in order) for maximum RF output . Recheck power across entire freq range.
Re-adjust L44 for minimum SSB distortion.
SSB CARRIER BALANCE:
Set mode to USB

Set RF power control fully clockwise

MIKE GAIN to minimum.
Connect wattmeter to ANT output.
 
VR6
Key TX, adjust for min. carrier leakthrough on scope or wattmeter. Recheck on LSB mode. If necessary readjust for best balance of sideband suppression between LSB & USB
SSB APC:
Set mode to USB

Set RF power fully clockwise.
MIKE GAIN to minimum.
Connect DC voltmeter from pcb ground to TP7
VR17
In TX, adjust for 8.5vdc
SSB ALC:
Mode to USB. 

MIKE GAIN to maximum. 

Inject two-tone audio signal of 700Hz and 1900Hz, 30 mV to Mic input.
Connect wattmeter to ANT output.
 
VR13


L44
In TX, adjust for 
100 watts PEP.

Adjust for minimum distortion on scope
AM CARRIER POWER:
Set mode to AM, 

MIKE GAIN at minimum.

RF Power SW to HI.
Connect wattmeter to ANT output.
CAUTION! Do not exceed power levels. Damage to power transistors and inability to achieve 100% modulation from insufficient audio power will result.

 VR14

Set RF PWR fully clockwise
adjust VR14 for 40 watts 
VR18
Set RF PWR fully counter clockwise.
Adjust for 10 watts
RF METER:
Set mode to AM,

RF Power fully clockwise
MIKE GAIN at minimum.

Meter Switch to PWR
Connect wattmeter to ANT output.
VR9
Adjust so meter agrees with Wattmeter.
AMC:
Mode to AM. 

RF Power fully clockwise
MIKE GAIN to maximum. 

Inject audio signal of 1KHz at 30mV to Mic input.
Connect modulation meter to ANT output.
VR16
Adjust for 100% modulation depth.
MODULATION METER:
Mode to AM. 

RF Power fully clockwise
MIKE GAIN to maximum.

Meter Switch to MOD

Inject audio signal of 1KHz at 30mV to Mic input.
Connect modulation meter to ANT output.
VR15
Adjust so meter agrees with modulation meter.
Mod Lamp Adjust:
Mode to AM. 

RF Power fully clockwise
MIKE GAIN to maximum.

Front Panel Switch to Mod Lamp
Inject audio signal of 1KHz at 30mV to Mic input.
Connect modulation meter to ANT output.
VR910
Adjust so that lamp illuminates at approx. 75% modulation
FM DEVIATION:
Mode to FM

MIKE GAIN to maximum. 

Inject 1 KHz, 30 mV audio signal at mike jack.
Connect deviation meter to ANT output.
VR5
Adjust for total deviation of 4.5 KHz.

Copyright © 2004 CBTricks.com

Disclaimer: Although the greatest care has been taken while compiling these documents,
we cannot guarantee that the instructions will work on every radio presented.